爱华网1.刀口型直尺:knife straigjht edge
2.刀口尺: knife straigjht edge
3.三棱尺three edges straigjht edge
4.四棱尺four edges straigjht edge
5.条式和框式水平仪
bar form and square levels
6.合像水平仪 imaging level meter
7铸铁平板 cast iron surface plate
8.岩石平板 granite surface plate
9.铸铁平尺cast iron straigjht edge
10.钢平尺和岩石平尺
steel and granite straigjht edge
11.圆度仪 roundness measuring instrument
12.电子水平仪electronic level meter
13.表面粗糙度比较样块铸造表面 roughness comparison specimens cast surface
14.表面粗糙度比较样块磨、车、铣、插及刨加工表面
roughness comparison specimens-ground,turned,bored,milled,shape andplaned
15.表面粗糙度比较样块电火花加工表面
roughness comparison specimens spark-erostion machiningsurfaces
16.表面粗糙度比较样块抛光加工表面
roughness comparison specimens pollshed surfaces
17.接触式仪器的标称特性
18.轮廓profiles
19.轨迹轮廓 traced profile
20.基准轮廓 reference profile
21.总轮廓 total profile
22.原始轮廓 primary profile
23.残余轮廓residual profile
24.触针式仪器stylus instrument
25.感应位移数字存储触针式量仪displacement sensitive,digitally storing stylusinstrument
26.触针式仪器的部件stylus instrument components
27.测量环measurement loop
28.导向基准renfence guide
29.驱动器drive unit
30.测头(传感器)probe(pick-up)
31.拾取单元tracing element
32.针尖stylus tip
33.转换器transducer
34.放大器amplifier
35.模/数转换器analog-to-digital converter
36.数据输入data input
37.数据输出data output
38.轮廓滤波和评定profile filtering and evaluation
39.轮廓记录器profile recorder
40.仪器的计量特性metrological characteristics of the instrument
41.静测力的变化change of static measuring force
42.静态测力 static measuring force
43.动态测量力 dynamic measuring force
44.滞后hysteresis
45.测头的测量范围 transmission function for the sine waves
46.仪器的测量范围measuring range of the instrument
47.模数转换器的量化步距quantization step of the ADC
48.仪器分辨力 instrument resolution
49.量程分辨力比range-to-resolution ratio
50.测头线性偏差probe linearity deviation
51.短波传输界限short-wave transmission limitation
52.轮廓垂直成分传输 vertical profile component transmission
53表面粗糙度比较样块抛丸、喷砂加工表面
roughness comparison specimens shot blasted and blastedsurfaces
54产品结构几何量计术规范（GPS）geometrical product specifications(GPS)
55表面结构 surface texture
56接触式仪器的标称特性 nominal characteristics of contact instruments
57公法线千分尺micrometer for mearsuring root tangent lenghths of gearteeth
58最大允许误差 maximum permissible error
59圆柱直齿渐开线花键量规 gauges for straight cylindrical involutesplines
60齿厚游标卡尺 Gear tooth vernier
calipers
61齿轮渐开线样板the involute master of gear
62齿轮螺旋线样板 the helix master of gear
63矩形花键量规 gauges for straight –sided splines
64测量蜗杆 master worm
65万能测齿仪 universal gear measuring instrument
66万能渐开线检查仪universal involute measuring instrument
67齿轮齿距测量仪gear circular pictch measuring instrument
68万能齿轮测量机 Universal gear measuring machine
69齿轮螺旋线测量仪gear helix measuring instrument
70便携式齿轮齿距测量仪 manual gear circular pitch measuring instrument
71便携式齿轮基节测量仪manual gear base pitch measuring instrument
72立式滚刀测量仪vertical hob measuring instrument
73齿轮双面啮合综合测量仪Gear dual-flank measuring instrument
74齿轮单面啮合整体误差测量仪Gear single-flank meshing integrated error measuringinstrument
75梯形螺纹量规 gauges for metric trapezoidal screw threads
76工作螺纹量规work gauges for metric trapezoidal screw threads
77校对螺纹量规check gauges for metric trapezoidal screw threads
78.梯形螺纹量规型式与尺寸 Types and dimensions of metric trapezoidal screwthreads
79.普通螺纹量规型式与尺寸 Types and dimensions of gauges purpose screwthreads
80.非螺纹密封的管螺纹量规 Gauges for pipe threads prcessure-tight joints arenot made on the threads
81.螺纹千分尺
Screw thread micrometer
82.最大允许误差 maximum permissible error
83.间隙螺纹量规 Clearance screw gauge
84.量针
Bar gauge
85.螺纹样板 Screw thread template
86.用螺纹密封的管螺纹量规
Gauges for pipe threads where pressure-tight joints are made on thethreads
87.刀具预调测量仪 精度
Accuracy of the presetting instrument
88.薄膜式气动量仪
Membrane type pneumatic measuring instrument
89.光栅线位移测量系统
Grating linear displacement measuring system
90.光栅角位移测量系统
Grating angular displacement measuring system
91.磁栅线位移测量系统
Magnet-grid linear displacement measuring system
92.量块附件
Accessories for gauge blocks
93.V形架
Vee blocks
94.比较仪座
Comparator stand
95.磁性表座
Magnetic stand
96.万能表座
Universal stand for dial indicator
一般术语：
1. 几何量 geometricalproduct
2. 量值value(of aquantity)
3. 真值true value(of aquantity)
4. 约定真值 conventional truevalue(of a quantity)
5. 单位unit(ofmeasurement)
6. 测量measurement
7. 测试measurement andtest
8. 检验inspecte
9. 静态测量staticmeasurement
10. 动态测量dynamicmeasurement
11. 测量原理principle ofmeasurement
12. 测量方法method ofmeasurement
13. 测量程序measurementprocedure
14. 被测量measurand
15. 影响量influencequantity
16. 变换值transformed value(of ameasurand)
17. 测量信号measurementsignal
18. 直接测量法direct method ofmeasurement
19. 间接测量法indirect method ofmeasurement
20. 定义测量法definitive method ofmeasurement
21. 直接比较测量法direct-comparisonmethod of measurement
22. 替代测量法substitution methodof measurement
23. 微差测量法differential methodof measurement
24. 零位测量法nulll method ofmeasurement
25. 测量结果result of ameasurement
26. 测得值measured value
27. 实际值actual value
28. 未修正结果uncorrected result（of a measurement）
29. 已修正结果corrected result(of ameasurement)
30. 测量的准确度accuracy ofmeasurement
31. 测量的重复性repeatability ofmeasurement
32. 测量复现性reproducibility ofmeasurements
33. 实验标准偏差experimentalstandard deviation
34. 测量不确定度uncertainty ofmeasurement
35. 测量绝对误差 absolute error ofmeasurement
36. 相对误差 relative error
37. 随机误差random error
38. 系统误差 systematicerror
39. 修正值correction
40. 修正系数correctionfactor
41. 人员误差personal error
42. 环境误差environmentalerror
43. 方法误差error of method
44. 调整误差adjustment error
45. 读数误差reading error
46. 视差parallax error
47. 估读误差 interpolationerror
48. 粗大误差parasitic error
49. 检定verification
50. 校准calibration
51. 调准gauging
52. 调整adjustment
几何量测量器具术语
1. 几何量具测量器具dimensionalmeasuring instruments
2. 长度测量器具length measuringinstruments
3. 角度测量器具angle measuringinstruments
4. 坐标测量机coordinate measuringmachine
5. 形状和位置误差测量器具form andposition error measuring instruments
6. 表面质量测量器具surface qualitymeasuring instruments
7. 齿轮测量器具gear measuringinstruments
8. 实物量具（简称“量具”）materialmeasure
9. 测量仪器（简称“量仪”）measuringinstruments
10. 测量链measuring chain
11. 测量装置measuring system
12. 指示式测量仪器indicating(measuring )instrument
13. 记录式测量仪器recording（measuring）instrument
14. 累计式测量仪器totalizing(measuring)instrument
15. 积分式测量仪器integrating(measuring)instrument
16. 模拟式测量仪器analogue(measuring)instrument
17. 数字式测量仪器digital(measuring)instrument
18. 测量变换器measuringtransducer
19. 传感器sensor
20. 指示装置indicatingdevice
21. 记录装置recording device
22. 记录载体recording medium
23. 标尺标记scale mark
24. 指示器index
25. 标尺scale
26. 度盘dail
测量器具术语
1. 标称值nominal value
2. 示值indication(of a measuringinstrument)
3. 标尺范围scale range
4. 标称范围nominal range
5. 标尺长度scale length
6. 标尺分度scale division
7. 分度值value of a scaledivision
8. 标尺间距scale spacing
9. 线性标尺linear scale
10. 非线性标尺non-linearscale
11. 标尺标数scale numbering
12. 测量仪器的零位zero of a measuringinstrument
13. 量程span
14. 测量范围measuring range
15. 额定工作条件vated operatingconditions
16. 极限条件referencecondition
17. 标准条件referencecondition
18. 仪器常数instrumentconstant
19. 响应特性responsecharacteristic
20. 灵敏度senstivity
21. 鉴别力discrimination
22. 分辨力resolution（of anindicating device）
23. 死区dead band
24. 准确度accuracy of a measuringinstruments
25. 准确度等级accuracy class
26. 重复性repeatability of ameasuring instrument
27. 示值变动性varation ofindication
28. 稳定度stability
29. 可靠性reliability
30. 回程hysteresis
31. 漂移drift
32. 响应时间response time
33. 测量力（简称“测力”）measuringforce
测量器具术语
1. 实物量具示值误差error of indicationof a material measure
2. 测量仪器示值误差error of indicationof a measuring instrument
3. 重复性误差repeatability error ofa measuring instrument
4. 回程误差hysteresis error
5. 测量力变化variation of measuringforce
6. 测量力落差hysteresis ofmeasuring force
7. 偏移误差bias error (of ameasuring instrument)
8. 允许误差maximum permissibleerrors(of measuring instruments)
9. 跟踪误差tracking error (of ameasuring instrument)
10. 响应率误差response-law error(of a measuring instrument)
11. 量化误差quantization error (ofa measuring instrument)
12. 基值误差datum error (of ameasuring instrument)
13. 零值误差zero error (of ameasuring instrument)
14. 影响误差influence error
15. 引用误差fiducial error
16. 位置误差position error
17. 线性误差linear error
18. 响应特性曲线responsecharacteristic curve
19. 误差曲线error curve
20. 校准曲线calibrationcurve
21. 修正曲线correction curve
长度测量器具量具类
1.量块gaugeblock
2.光滑极限量规plainlimit gauge
3.塞规pluggauge
4.环规ringgauge
卡规snap gauge
5.塞尺feelergauge
6.钢直尺steelgauge
7.精密玻璃线纹尺precisionglass linear scale
8.精密金属线纹尺precisionmetal linear scale
9.半径样板radiustemplate
卡尺类
1.游标卡尺verniercaliper
2.带表卡尺dialcaliper
3.电子数显卡尺calliperwith electronic digital display
4.深度标游卡尺depthvernier caliper
5.电子数显深度卡尺depthcaliper with electronic digital display
6.带表高度卡尺dialheight calliper
7.高度游标卡尺heightvernier caliper
8.电子数显高度卡尺heightcaliper with electronic digital display
9.焊接检验尺calliperfor welding inspection
千分尺类
1.测微头micrometerhead
2.外径千分尺externalmicrometer
3.杠杆千分尺micrometerwith dial comparator
4.带计数器千分尺micrometerwith counter
5.电子数显外径千分尺micrometerwith electronic digital display
6.小测头千分尺smallanvil micrometer
7.尖头千分尺pointmicrometer
8.板厚千分尺sheetmetal micrometer
9.壁厚千分尺tubemicrometer
10.叶片千分尺blademicrometer
11.奇数沟千分尺oddfluted micrometer
12.深度千分尺depthmicrometer
13.内径千分尺internalmicrometer
14.单杆式内径千分尺single-bodyinternal micrometer
15.表式内径千分尺dail internal micrometer
16.三爪式内径千分尺threepoint internal micrometer
17.电子数显三爪式内径千分尺threepoint internal micrometer
18.内测千分尺insidemicrometer
指示表类
1.指示表dial indicator
2.深度只是表depthdial indicator
3.杠杆指示表dialtest indicator
4.内径指示表boredial indicator
5.涨弹簧式指示表expanding head bore dial indicator
6.钢球式内径指示表balltype bore dial indicator
7.电子数显指示表dialindicator with electronic digital display
8.杠杆卡规indicatingsnap gauge
9.带表卡规dialsnap gauge
10.带表外卡规outsidedial snap gauge
11.带表内卡规insidedial snap gauge
12.测厚规thicknessgauge
13.扭簧比较仪microcator
14.杠杆齿轮比较仪mechanicaldial comparator
15.电子量规electronicgauge
16.电感式传感器inductancetype transducer
17.指示装置indicatingdevice
18.电感测微仪inductancemicrometer
19.峰值电感测微仪peakinductance micrometer
20.电感内径比较仪inductancebore comparator
21.瞄准传感器aimingtransducer
角度测量器具
1.角度块angleblock gauge
2.正多面棱体regularpolygon mirror
3.刀具角度样板cutterangular template
4.直角尺square
5.平行直角尺parallelsquare
6.宽座直角尺wide-standsquare
7.刀口形直角尺edgesquare
8.矩形直角尺squaresquare
9.三角形直角尺threeangle square
10.圆柱直角尺cylindersquare
11.方形角尺squareguage
12.万能角度尺universalbevel protractor
13.游标式万能角度尺vernieruniversal bevel protractor
14.表式万能角度尺dialuniversal bevel protractor
15.光学分度头opticaldividing head
16.目镜式光学分度头opticaldividing head with microscope reading
17.投影式光学分度尺opticaldividing head with projection reading
18.光电分度头optical-electronicdividing head
19.多齿分度台multi-toothdivision table
20.分度转台divisionrotary table
21.正炫规sinebar
22.普通正炫规generalsine bar
23.铰链式正炫规hingetype sine bar
24.双向正炫规dual-directionalsine bar
25.圆锥量规conegauge
26.圆锥塞规plugcone gauge
27.圆锥环规ringcone gauge
28.直角尺测量仪squaremeasuring instrument
形位误差测量器具1.平晶opticalflat
2.单面平晶opticalflat
3.双面平晶paralleloptical flat
4.刀口形直尺knifestraight edge
5.刀口尺knifestraight edge
6.三棱尺threeedges straight edge
7.四棱尺fouredges straight edge
8.平尺straightedge
9.矩形平尺squarestraight edge
10.工字形平尺i-beamstraight edge
11.角形平尺anglestraight edge
12.桥形平尺bridgetype straight edge
13.平板surfaceplate
14.铸铁平板castiron surface plate
15.岩石平板granitesurface plate
16.方箱squarebox
17.水准器式水平仪levelmeter
18.条式水平仪barlevel meter
19.框式水平仪framelevel meter
20.合像水平仪imaginglevel meter
21.光学倾斜仪opticalinclinometer
22.电子水平仪electroniclevel meter
23.指针式电子水平仪electroniclevel meter with indicator
24.数显式电子水平仪electroniclevel meter with digital display
25.平直度测量仪straightnessmeasuring instrument
26.光学式平直度测量仪opticalstraightness measuring instrument
27.光电式平直度测量仪photoelectricalstraightness measuring instrument
28.圆度测量仪roundnessmeasuring instrument
29.转轴式圆度测量仪spindle-rotatingtype roundness measuring instrument
30.转台式圆度测量仪table-rotatingtype roundness measuring instrument
表面质量测量器具表面粗糙度比较样块surface roughnesscomparison specimen
铸造表面粗糙度比较样块surface roughness comparison specimen for castsurface
磨、车、镗、铣、插及刨加工表面粗糙度比较样块surface roughness comparison specimen forground,turned,bored,milled,shaped and planed surface
电火花加工表面粗糙度比较样块surface roughness comparison specimen forspark-erosion machined surface
抛（喷）丸、喷砂加工表面粗糙度比较样块surface roughness comparison specimen for shotblasted and grit blasted surface
抛光加工表面粗糙度测量仪portable surface roughness comparison specimen forpolished surface
便携式表面粗糙度测量仪portable surface roughess measuring instrument
驱动箱driving box
台式表面粗糙度测量仪bench type surface roughness measuring instrument
