netgear交换机设置 netgear交换机怎么设置

美国网件(NETGEAR)交换机怎么设置??部分用户在向小编咨询这个问题。为此,小编专门整理了这篇文章,告诉大家如何设置网件(NETGEAR)路由器的交换机。

###netgear交换机设置方法

1. 用网线连接FSM726S交换机的26端口和配置用的电脑。

2. 打开IE浏览器,在URL处输入Http://192.168.0.240/; 进入FSM726交换机的WEB管理界面 (缺省无管理员口令), 将FSM726交换机恢复出厂设置 (Factory Reset)。等FSM726交换机重启动完毕,使用9针串口设置线进入CLI管理控制界面配置管理IP地址:192.168.0.240/24

3.打开配置计算机的IE浏览器,进入FSM726的管理配置界面,点选菜单Advanced>VLANs>Primary VLAN菜单;

4.在Primary VLAN菜单内,我们为Default Vlan选项进行VLAN端口的标记定义,保留1,23,24,25,26为U,其余置空;

5.在Show VLAN菜单内,选择Add a new VLAN选项增加新VLAN4,Name设置为vlan4,VLAN ID设置为4,端口选择1,24为U,其余置空;

6.重复第4步动作,在Show VLAN菜单内,选择Add a new VLAN选项增加新VLAN4,Name设置为vlan5,VLAN ID设置为5,端口选择23,24为U,其余置空

7.选择Advanced>VLANS里的VLAN Ports,在该页设置端口的PVID,将1端口的PVID改为4,23端口的PVID改成5,其余保留

8. 最后在Tools>Save Configuration页面保存设置。这样1端口和23端口的用户分别在2个不同的802.1q VLAN,24口同时属于vlan1,4,5连接上一级交换机。

1. 进入端口E0/1的配置视图 [SwitchA]interface Ethernet 0/1

2. 对端口E0/1的出方向报文进行流量限速,限制到3Mbps [SwitchA- Ethernet0/1]line-rate outbound 30

3. 对端口E0/1的入方向报文进行流量限速,限制到1Mbps [SwitchA- Ethernet0/1]line-rate inbound 16

【补充说明】

报文速率限制级别取值为1~127。如果速率限制级别取值在1~28范围内,则速率限制的粒度为64Kbps,这种情况下,当设置的级别为N,则端口上限制的速率大小为N*64K;如果速率限制级别取值在29~127范围内,则速率限制的粒度为1Mbps,这种情况下,当设置的级别为N,则端口上限制的速率大小为(N-27)*1Mbps。 此系列交换机的具体型号包括:S2008-EI、S2016-EI和S2403H-EI。 『S2000-SI和S3000-SI系列交换机端口限速配置流程』 使用以太网物理端口下面的line-rate命令,来对该端口的出、入报文进行流量限速。

【SwitchA相关配置】

1. 进入端口E0/1的配置视图 [SwitchA]interface Ethernet 0/1

2. 对端口E0/1的出方向报文进行流量限速,限制到6Mbps

[SwitchA- Ethernet0/1]line-rate outbound 2

3. 对端口E0/1的入方向报文进行流量限速,限制到3Mbps

[SwitchA-Ethernet0/1]line-rate inbound

设置Netgear 7000系列交换机

(GSM7212,GSM7224,GSM7248,FSM7326P,FSM7328S,FSM7352S,FSM7352PS,GSM7312,GSM7324)的VLAN

请注意:FSM7328S,FSM7352S,FSM7352PS在设置里面的端口表示方法与其他7000系列交换机不同,其中物理端口其他7000系列交换机是Interface 0/2,在FSM73xxS可堆叠交换机里应为Interface 1/0/2。

一、通过Web页面设置 NETGEARGSM7312交换机Port-Base Vlan

设置目标:

增加2个Vlan:Vlan6(端口1);Vlan7(端口12),这2个Vlan间的用户不能互相访问,但可以通过共同端口11口访问路由器,其余端口保留在Vlan1。

配置步骤

使用9针串口设置线连接GSM7312交换机,进入CLI配置界面,使用(GSM7312)# Clear Config命令恢复出厂设置。

然后使用命令(GSM7312)#Reload ; 系统提示是否保存现有配置(选择YES)。然后系统重新启动。

配置GSM7312交换机管理IP地址为192.168.0.238/24,配置完毕后保存。

连接配置计算机的网线到GSM7312的端口10;

打开IE浏览器,在URL处输入http://192.168.0.238/,进入交换机配置管理界面。

点选菜单Switch>VLAN>config ;在VLAN Configuration界面的Default VLAN处选择进行端口配置,保留所有端口在VLAN1不动;

在VLAN Configuration界面的VLAN ID and Name处,下拉选择Create选项进行新的VLAN的创建。

8.在VLAN ID栏里输入6; VLAN Name处输入:VLAN6 ;

VLAN type选:Static(缺省)

然后,按住键盘CTRL的同时,用鼠标点在unTag栏目下点选端口1、11,然后点“Submit”按纽保存设置。(见下图)

9.重复7-8步骤过程,建立VLAN7,添加端口11,12

10.点选菜单Switch>VLAN>Port config ;在Port Vlan ID右边栏里输入:6;点选端口1;然后按”Submit”更改端口1的PVID;

11.重复第10步,在Port Vlan ID右边栏里输入:7;点选端口12;然后按”Submit”更改端口12的PVID;

12.选择菜单薄Switch>VLAN>status ,查看VLAN包含端口情况,VLAN1应包含所有端口,Vlan6包含1,11端口,Vlan7包含11,12端口。

13.在Switch>VLAN>Port config页下面查看端口的PVID,1端口应为6,12端口应为7,其余为1。

14.设置完成。

二、通过CLI命令行设置 NETGEARGSM7312交换机Port-Base Vlan

(GSM7312) >enable

Password:

(GSM7312) #vlan database

//进入VLAN设置

(GSM7312) (Vlan)#vlan 6

//创建Vlan6

(GSM7312) (Vlan)#vlan name 6 vlan6

//设置VLAN6名字

(GSM7312) (Vlan)#vlan 7

(GSM7312) (Vlan)#vlan name 7 vlan7

(GSM7312) (Vlan)#exit

(GSM7312) #configure

//进入全局配置模式

(GSM7312) (Config)#interface 0/1

//进入端口配置模式

(GSM7312) (Interface 0/1)#vlan participation include 6

//设置端口属于VLAN 6

(GSM7312) (Interface 0/1)#no vlan tagging 6

//端口不打Tag标记

(GSM7312) (Interface 0/1)#vlan pvid 6

//设置端口PVID

(GSM7312) (Interface 0/1)#exit

(GSM7312) (Config)#interface 0/11

(GSM7312) (Interface 0/11)#vlan participation include 6

(GSM7312) (Interface 0/11)#vlan participation include 7

(GSM7312) (Interface 0/11)#no vlan tagging 6

(GSM7312) (Interface 0/11)#no vlan tagging 7

(GSM7312) (Interface 0/11)#exit

(GSM7312) (Config)#interface 0/12

(GSM7312) (Interface 0/12)#vlan participation include 7

(GSM7312) (Interface 0/12)#no vlan tagging 7

(GSM7312) (Interface 0/12)#vlan pvid 7

(GSM7312) (Interface 0/12)#exit

(GSM7312) (Config)#exit

(GSM7312) #copy system:running-config nvram:startup-config

//存盘

Are you sure you want to save? (y/n) y

Configuration Saved!

(GSM7312) #show vlan 1

//查看Vlan1状态

VLAN ID: 1

VLAN Name: Default

VLAN Type: Default

slot/portCurrentConfiguredTagging

-------------------------------------

0/1IncludeIncludeUntagged

0/2IncludeIncludeUntagged

0/3IncludeIncludeUntagged

0/4IncludeIncludeUntagged

0/5IncludeIncludeUntagged

0/6IncludeIncludeUntagged

0/7IncludeIncludeUntagged

0/8IncludeIncludeUntagged

0/9IncludeIncludeUntagged

0/10IncludeIncludeUntagged

0/11IncludeIncludeUntagged

0/12IncludeIncludeUntagged

(GSM7312) #show vlan 6

VLAN ID: 6

VLAN Name: vlan6

VLAN Type: Static

slot/portCurrentConfiguredTagging

-------------------------------------

0/1IncludeIncludeUntagged

0/2ExcludeAutodetectUntagged

0/3ExcludeAutodetectUntagged

0/4ExcludeAutodetectUntagged

0/5ExcludeAutodetectUntagged

0/6ExcludeAutodetectUntagged

0/7ExcludeAutodetectUntagged

0/8ExcludeAutodetectUntagged

0/9ExcludeAutodetectUntagged

0/10ExcludeAutodetectUntagged

0/11IncludeIncludeUntagged

0/12ExcludeAutodetectUntagged

(GSM7312) #show vlan 7

VLAN ID: 7

VLAN Name: vlan7

VLAN Type: Static

slot/portCurrentConfiguredTagging

-------------------------------------

0/1ExcludeAutodetectUntagged

0/2ExcludeAutodetectUntagged

0/3ExcludeAutodetectUntagged

0/4ExcludeAutodetectUntagged

0/5ExcludeAutodetectUntagged

0/6ExcludeAutodetectUntagged

0/7ExcludeAutodetectUntagged

0/8ExcludeAutodetectUntagged

0/9ExcludeAutodetectUntagged

0/10ExcludeAutodetectUntagged

0/11IncludeIncludeUntagged

0/12IncludeIncludeUntagged

(GSM7312) #show vlan port all

PortAcceptableIngressDefault

slot/port VLAN ID Frame TypesFilteringGVRPPriority

--------- ------- ------------ ----------- ------- --------

0/16Admit AllDisableDisable0

0/21Admit AllDisableDisable0

0/31Admit AllDisableDisable0

0/41Admit AllDisableDisable0

0/51Admit AllDisableDisable0

0/61Admit AllDisableDisable0

0/71Admit AllDisableDisable0

0/81Admit AllDisableDisable0

0/91Admit AllDisableDisable0

0/101Admit AllDisableDisable0

0/111Admit AllDisableDisable0

0/127Admit AllDisableDisable0

(GSM7312) #

三、.通过Web页面设置 NETGEARGSM7312交换机802.1Q Vlan

设置目标:

在GSM7312上增加建立6个Vlan:Vlan2-7,其中端口1打标记属于VLAN2、VLAN3,端口12打标记属于VLAN4、VLAN5,2-5端口不打标记属于VLAN6,6-9端口不打标记属于VLAN7,10端口不打标记属于VLAN1,11端口打标记属于所有VLAN与上级交换机上连。

端口PVIDVLAN1VLAN2VLAN3VLAN4VLAN5VLAN6VLAN7

11TTT

26U

36U

46U

56U

67U

77U

87U

97U

107U

111TTTTTTT

121TTT

配置步骤

1. 使用9针串口设置线连接GSM7312交换机,进入CLI配置界面,使用(GSM7312)# Clear Config命令恢复出厂设置。

2.然后使用命令(GSM7312)#Reload ; 系统提示是否保存现有配置(选择YES)。然后系统重新启动。

3.配置GSM7312交换机管理IP地址为192.168.0.238/24,配置完毕后保存。

4.连接配置计算机的网线到GSM7312的端口10;

5. 打开IE浏览器,在URL处输入http://192.168.0.238/,进入交换机配置管理界面。

6. 点选菜单Switch>VLAN>config ;在VLAN Configuration界面的Default VLAN处选择进行端口配置,1,11,12标记在Tagged、10标记在Untagged;

7. 在VLAN Configuration界面的VLAN ID and Name处,下拉选择Create选项进行新的VLAN的创建。

8.在VLAN ID栏里输入2; VLAN Name处输入:VLAN2 ;

VLAN type选:Static(缺省)

然后,按住键盘CTRL的同时,用鼠标点在Tagged栏目下点选端口1、11,然后点“Submit”按纽保存设置。(见下图)

重复7-8步骤过程,建立VLAN3,添加端口1,11在Tagged。建立VLAN4,VLAN5添加端口11,12在Tagged。

VLAN3:

VLAN4:

VLAN5:

//查看Vlan1状态

VLAN ID: 1

VLAN Name: Default

VLAN Type: Default

slot/portCurrentConfiguredTagging

-------------------------------------

0/1IncludeIncludeUntagged

0/2IncludeIncludeUntagged

0/3IncludeIncludeUntagged

0/4IncludeIncludeUntagged

0/5IncludeIncludeUntagged

0/6IncludeIncludeUntagged

0/7IncludeIncludeUntagged

0/8IncludeIncludeUntagged

0/9IncludeIncludeUntagged

0/10IncludeIncludeUntagged

0/11IncludeIncludeUntagged

0/12IncludeIncludeUntagged

(GSM7312) #show vlan 6

VLAN ID: 6

VLAN Name: vlan6

VLAN Type: Static

slot/portCurrentConfiguredTagging

-------------------------------------

0/1IncludeIncludeUntagged

0/2ExcludeAutodetectUntagged

0/3ExcludeAutodetectUntagged

0/4ExcludeAutodetectUntagged

0/5ExcludeAutodetectUntagged

0/6ExcludeAutodetectUntagged

0/7ExcludeAutodetectUntagged

0/8ExcludeAutodetectUntagged

0/9ExcludeAutodetectUntagged

0/10ExcludeAutodetectUntagged

0/11IncludeIncludeUntagged

0/12ExcludeAutodetectUntagged

(GSM7312) #show vlan 7

VLAN ID: 7

VLAN Name: vlan7

VLAN Type: Static

slot/portCurrentConfiguredTagging

-------------------------------------

0/1ExcludeAutodetectUntagged

0/2ExcludeAutodetectUntagged

0/3ExcludeAutodetectUntagged

0/4ExcludeAutodetectUntagged

0/5ExcludeAutodetectUntagged

0/6ExcludeAutodetectUntagged

0/7ExcludeAutodetectUntagged

0/8ExcludeAutodetectUntagged

0/9ExcludeAutodetectUntagged

0/10ExcludeAutodetectUntagged

0/11IncludeIncludeUntagged

0/12IncludeIncludeUntagged

(GSM7312) #show vlan port all

PortAcceptableIngressDefault

slot/port VLAN ID Frame TypesFilteringGVRPPriority

--------- ------- ------------ ----------- ------- --------

0/16Admit AllDisableDisable0

0/21Admit AllDisableDisable0

0/31Admit AllDisableDisable0

0/41Admit AllDisableDisable0

0/51Admit AllDisableDisable0

0/61Admit AllDisableDisable0

0/71Admit AllDisableDisable0

0/81Admit AllDisableDisable0

0/91Admit AllDisableDisable0

0/101Admit AllDisableDisable0

0/111Admit AllDisableDisable0

0/127Admit AllDisableDisable0

(GSM7312) #

三、.通过Web页面设置 NETGEARGSM7312交换机802.1Q Vlan

设置目标:

在GSM7312上增加建立6个Vlan:Vlan2-7,其中端口1打标记属于VLAN2、VLAN3,端口12打标记属于VLAN4、VLAN5,2-5端口不打标记属于VLAN6,6-9端口不打标记属于VLAN7,10端口不打标记属于VLAN1,11端口打标记属于所有VLAN与上级交换机上连。

端口PVIDVLAN1VLAN2VLAN3VLAN4VLAN5VLAN6VLAN7

11TTT

26U

36U

46U

56U

67U

77U

87U

97U

107U

111TTTTTTT

121TTT

配置步骤

1. 使用9针串口设置线连接GSM7312交换机,进入CLI配置界面,使用(GSM7312)# Clear Config命令恢复出厂设置。

2.然后使用命令(GSM7312)#Reload ; 系统提示是否保存现有配置(选择YES)。然后系统重新启动。

3.配置GSM7312交换机管理IP地址为192.168.0.238/24,配置完毕后保存。

4.连接配置计算机的网线到GSM7312的端口10;

5. 打开IE浏览器,在URL处输入http://192.168.0.238/,进入交换机配置管理界面。

6. 点选菜单Switch>VLAN>config ;在VLAN Configuration界面的Default VLAN处选择进行端口配置,1,11,12标记在Tagged、10标记在Untagged;

7. 在VLAN Configuration界面的VLAN ID and Name处,下拉选择Create选项进行新的VLAN的创建。

8.在VLAN ID栏里输入2; VLAN Name处输入:VLAN2 ;

VLAN type选:Static(缺省)

然后,按住键盘CTRL的同时,用鼠标点在Tagged栏目下点选端口1、11,然后点“Submit”按纽保存设置。(见下图)

重复7-8步骤过程,建立VLAN3,添加端口1,11在Tagged。建立VLAN4,VLAN5添加端口11,12在Tagged。

VLAN3:

VLAN4:

VLAN5:

9. 重复7-8步骤过程,建立VLAN6,添加端口2-5端口在Untagged,11在Tagged。建立VLAN7,添加端口6-9端口在Untagged,11在Tagged。

VLAN6:

VLAN7:

10.点选菜单Switch>VLAN>Port config ;在Port Vlan ID右边栏里输入:1;点选端口1,11,12;然后按”Submit”更改端口1,10,11,12的PVID;

11.重复第10步,在Port Vlan ID右边栏里输入:6;点选端口2-5;然后按”Submit”更改端口2-5的PVID;在Port Vlan ID右边栏里输入:7;点选端口6-9;然后按”Submit”更改端口6-9的PVID;

2-5:

6-9:

12.选择菜单薄Switch>VLAN>status ,查看VLAN包含端口情况,VLAN1应包含1,10,11,12端口,Vlan2,Vlan3包含1,11端口,Vlan4,Vlan5包含11,12端口,Vlan6包括2-5,11端口,Vlan7包括6-9,11端口。

13.在Switch>VLAN>Port config页下面查看端口的PVID,2-5端口应为6,6-9端口应为7,其余为1。

14.设置完成。

四、通过Web页面设置 NETGEARGSM7312交换机802.1Q Vlan

(GSM7312) >enable

Password:

(GSM7312) #vlan database

(GSM7312) (Vlan)#vlan 2

(GSM7312) (Vlan)#vlan name 2 vlan2

(GSM7312) (Vlan)#vlan 3

(GSM7312) (Vlan)#vlan name 3 vlan3

(GSM7312) (Vlan)#vlan 4

(GSM7312) (Vlan)#vlan name 4 vlan4

(GSM7312) (Vlan)#vlan 5

(GSM7312) (Vlan)#vlan name 5 vlan5

(GSM7312) (Vlan)#vlan 6

(GSM7312) (Vlan)#vlan name 6 vlan6

(GSM7312) (Vlan)#vlan 7

(GSM7312) (Vlan)#vlan name 7 vlan7

(GSM7312) (Vlan)#exit

(GSM7312) #configure

(GSM7312) (Config)#interface 0/1

(GSM7312) (Interface 0/1)#vlan participation include 1

(GSM7312) (Interface 0/1)#vlan participation include 2

(GSM7312) (Interface 0/1)#vlan participation include 3

(GSM7312) (Interface 0/1)#vlan tagging 1

//端口打801.1q标记

(GSM7312) (Interface 0/1)#vlan tagging 2

(GSM7312) (Interface 0/1)#vlan tagging 3

(GSM7312) (Interface 0/1)#vlan pvid 1

(GSM7312) (Interface 0/1)#exit

(GSM7312) (Config)#interface 0/2

(GSM7312) (Interface 0/2)#vlan participation exclude 1

//设置端口不属于default vlan(vlan1)

(GSM7312) (Interface 0/2)#vlan participation include 6

(GSM7312) (Interface 0/2)#no vlan tagging 6

(GSM7312) (Interface 0/2)#vlan pvid 6

(GSM7312) (Interface 0/2)#exit

(GSM7312) (Config)#interface 0/3

(GSM7312) (Interface 0/3)#vlan participation exclude 1

(GSM7312) (Interface 0/3)#vlan participation include 6

(GSM7312) (Interface 0/3)#no vlan tagging 6

(GSM7312) (Interface 0/3)#vlan pvid 6

(GSM7312) (Interface 0/3)#exit

(GSM7312) (Config)#interface 0/4

(GSM7312) (Interface 0/4)#vlan participation exclude 1

(GSM7312) (Interface 0/4)#vlan participation include 6

(GSM7312) (Interface 0/4)#no vlan tagging 6

(GSM7312) (Interface 0/4)#vlan pvid 6

(GSM7312) (Interface 0/4)#exit

(GSM7312) (Config)#interface 0/5

(GSM7312) (Interface 0/5)#vlan participation exclude 1

(GSM7312) (Interface 0/5)#vlan participation include 6

(GSM7312) (Interface 0/5)#no vlan tagging 6

(GSM7312) (Interface 0/5)#vlan pvid 6

(GSM7312) (Interface 0/5)#exit

(GSM7312) (Config)#interface 0/6

(GSM7312) (Interface 0/6)#vlan participation exclude 1

(GSM7312) (Interface 0/6)#vlan participation include 7

(GSM7312) (Interface 0/6)#no vlan tagging 7

(GSM7312) (Interface 0/6)#vlan pvid 7

(GSM7312) (Interface 0/6)#exit

(GSM7312) (Config)#interface 0/7

(GSM7312) (Interface 0/7)#vlan participation exclude 1

(GSM7312) (Interface 0/7)#vlan participation include 7

(GSM7312) (Interface 0/7)#no vlan tagging 7

(GSM7312) (Interface 0/7)#vlan pvid 7

(GSM7312) (Interface 0/7)#exit

(GSM7312) (Config)#interface 0/8

(GSM7312) (Interface 0/8)#vlan participation exclude 1

(GSM7312) (Interface 0/8)#vlan participation include 7

netgear交换机设置 netgear交换机怎么设置

(GSM7312) (Interface 0/8)#no vlan tagging 7

(GSM7312) (Interface 0/8)#vlan pvid 7

(GSM7312) (Interface 0/8)#exit

(GSM7312) (Config)#interface 0/9

(GSM7312) (Interface 0/9)#vlan participation exclude 1

(GSM7312) (Interface 0/9)#vlan participation include 7

(GSM7312) (Interface 0/9)#no vlan tagging 7

(GSM7312) (Interface 0/9)#vlan pvid 7

(GSM7312) (Interface 0/9)#exit

(GSM7312) (Config)#interface 0/10

(GSM7312) (Interface 0/10)#vlan participation include 1

(GSM7312) (Interface 0/10)#no vlan tagging 1

(GSM7312) (Interface 0/10)#vlan pvid 1

(GSM7312) (Interface 0/10)#exit

(GSM7312) (Config)#interface 0/11

(GSM7312) (Interface 0/11)#vlan participation include 1

(GSM7312) (Interface 0/11)#vlan participation include 2

(GSM7312) (Interface 0/11)#vlan participation include 3

(GSM7312) (Interface 0/11)#vlan participation include 4

(GSM7312) (Interface 0/11)#vlan participation include 5

(GSM7312) (Interface 0/11)#vlan participation include 6

(GSM7312) (Interface 0/11)#vlan participation include 7

(GSM7312) (Interface 0/11)#vlan tagging 1

(GSM7312) (Interface 0/11)#vlan tagging 2

(GSM7312) (Interface 0/11)#vlan tagging 3

(GSM7312) (Interface 0/11)#vlan tagging 4

(GSM7312) (Interface 0/11)#vlan tagging 5

(GSM7312) (Interface 0/11)#vlan tagging 6

(GSM7312) (Interface 0/11)#vlan tagging 7

(GSM7312) (Interface 0/11)#vlan pvid 1

(GSM7312) (Interface 0/11)#exit

(GSM7312) (Config)#interface 0/12

(GSM7312) (Interface 0/12)#vlan participation include 1

(GSM7312) (Interface 0/12)#vlan participation include 4

(GSM7312) (Interface 0/12)#vlan participation include 5

(GSM7312) (Interface 0/12)#vlan tagging 1

(GSM7312) (Interface 0/12)#vlan tagging 4

(GSM7312) (Interface 0/12)#vlan tagging 5

(GSM7312) (Interface 0/12)#vlan pvid 1

(GSM7312) (Interface 0/12)#exit

(GSM7312) (Config)#exit

(GSM7312) #copy system:running-config nvram:startup-config

Are you sure you want to save? (y/n) y

Configuration Saved!

(GSM7312) #show vlan 1

VLAN ID: 1

VLAN Name: Default

VLAN Type: Default

slot/portCurrent ConfiguredTagging

-------------------------------------

0/1IncludeIncludeTagged

0/2ExcludeExcludeUntagged

0/3ExcludeExcludeUntagged

0/4ExcludeExcludeUntagged

0/5ExcludeExcludeUntagged

0/6ExcludeExcludeUntagged

0/7ExcludeExcludeUntagged

0/8ExcludeExcludeUntagged

0/9ExcludeExcludeUntagged

0/10IncludeInclude Untagged

0/11IncludeIncludeTagged

0/12IncludeIncludeTagged

(GSM7312) #show vlan 2

VLAN ID: 2

VLAN Name: vlan2

VLAN Type: Static

slot/portCurrentConfiguredTagging

-------------------------------------

0/1IncludeIncludeTagged

0/2ExcludeAutodetectUntagged

0/3ExcludeAutodetectUntagged

0/4ExcludeAutodetectUntagged

0/5ExcludeAutodetectUntagged

0/6ExcludeAutodetectUntagged

0/7ExcludeAutodetectUntagged

  

爱华网本文地址 » http://www.413yy.cn/a/222261/25713661.html

更多阅读

程控交换机原理 程控交换机怎么设置

电话交换机其实就是把外部电话号码进行一个空闲排队拨号的功能。举个列子说现在有电信3个号码??N1??N2??N3.传统是这3个号码直接接3个电话机,如果需要分机只能通过线路并联分线出来。相当于一个电话号,2个电话机的接法,这样有个弊端

网络交换机怎么设置 无线以太网交换机

如何进行交换机配置那是比较多的,要视具体情况而定,不作具体介绍,下一篇将要对交换机配置的常见应用--VLAN网络划分、配置方法进行详细介绍。 如果为交换机配置了名称,则也可以直接在”Telnet“命令后面空一个空格后输入交换机的名称,看

小区宽带路由器怎么设置 交换机怎么设置图解

小区宽带路由器怎么设置——简介小区宽带有很多种连接方式,也有的是光纤入户的。这里咱以普通的小区入网方式来看下各种连接方式的路由器怎么设置吧,其实也就是和普通的连接方式一样。由于光纤的连接方式在另一经验文章有讲,所以这里不

路由器如何当交换机用 路由器交换机怎么设置

有时,我们需要将路由器当交换机使用,下面就来详细讲解如何操作,这里设置了环境,下面来给大家分享如何把路由器当交换机使用吧。路由器如何当交换机用——工具/原料D-LINK504M路由器当交换机用华为MT800开启路由功能联想交换机环境:A办

电话交换机怎么设置 公司电话交换机设置

电话交换机又叫程控交换机,设置很简单程控交换机所有编程在8000分机上操作。输入正确的代码会有证实音,“嘟”的一声。(如无8000分机可以拨129查物理号,报000就是总机。)一,首先找到程控交换机的功能字头,由于出厂功能字头是“1”,重庆

声明:《netgear交换机设置 netgear交换机怎么设置》为网友第一顺位分享!如侵犯到您的合法权益请联系我们删除